2013-2019 Nissan NV200 Taxi Van MR20DE 2.0L Remanufactured Engine

Description

High-density cast aluminum alloy block architecture absorbs extreme combustion pressure spikes while hypereutectic aluminum pistons resist thermal expansion during grueling commercial transport operations in the Nissan NV200 Taxi MR20DE Remanufactured Engine engineered for 2013 to 2019 Nissan NV200 commercial taxi van fleet vehicles. This 16-valve DOHC inline-four platform restores high fuel economy and severe-duty multi-shift endurance.

Cast from lightweight aluminum alloy with cast-in iron cylinder liners, this severe-duty taxi engine incorporates a structural lower crankcase ladder bedplate that halts bottom-end deflection during round-the-clock idling. A micro-polished forged steel crankshaft turns within tri-metal bearings, linked to forged steel connecting rods and graphite-coated hypereutectic pistons. Cylinder decks receive an Ra 30 finish for MLS gasket sealing. Dry mass measures 270 lbs with a 4.2-quart capacity aluminum oil pan.

Key Features of Nissan NV200 Taxi

Municipal taxi fleet supervisors buy Nissan NV200 Taxi remanufactured engine packages to eliminate chronic vehicle downtime and maintain dependable passenger transit schedules. Every remanufactured long block undergoes vacuum decay testing to guarantee total fluid circuit separation before crate departure.

• Continuously variable valve timing phasers continuously adjust intake camshaft advance under load
• Dual overhead camshafts actuate sixteen valves via low-friction direct-acting mechanical bucket tappets
• 0.0010 to 0.0017 inch main bearing clearances maintain solid hydrodynamic lubrication film strength
• Multi-layer steel cylinder head gaskets maintain combustion seals across extreme summer city heat
• High-flow internal trochoid oil pumps channel pressurized lubricant to overhead camshaft journals
• Induction-hardened valve seats prevent valve face recession during continuous city stop-and-go driving
• Precision rotating package balancing protects Nissan NV200 Taxi driveline parts from vibration

NV200 Taxi Operational Combustion Limits

Operating lubricant pressure produces 16 to 22 PSI during warm idle and expands to 45 through 60 PSI at 2800 RPM cruise speeds. Internal coolant temperatures stabilize between 188°F and 202°F through regulated cross-flow cooling circulation. This 2.0-liter taxi engine generates 131 horsepower at 5200 RPM and 139 lb-ft continuous torque at 4800 RPM with a 9.7:1 compression ratio. Cylinder cranking pressure measures between 170 and 185 PSI across all four chambers. The cooling system rejects 1850 BTU per minute during loaded city transit.

NV200 Taxi Transaxle Alignment Thresholds

A 6-bolt rear crankshaft flange mounts flush to factory Xtronic CVT automatic transaxle driveplates. Measured crankshaft thrust endplay checks out between 0.0030 and 0.0070 inches. The 0.984-inch front crankshaft snout features a single keyway to position the timing chain drive gear and harmonic balancer, holding true accessory drive belt pulley alignment.

NV200 Taxi Fleet Servicing Protocols

Technicians must prime the engine oil pump prior to first startup by cranking the starter without ignition until oil pressure warning lamps extinguish. Fill the crankcase with 5W-30 motor oil meeting API service standards. This production engine is not engineered for turbocharging conversions, nitrous injection, or competitive track racing.

• Check crankcase oil level and coolant tank fluid volume each shift before driving
• Drain break-in motor oil and install fresh oil filter after 500 initial miles
• Perform routine oil and filter changes every 3750 miles during commercial transit cycles

NV200 Taxi Commercial Warranty Manifest

Commercial fleet purchasers receive a 3-Year / 100,000-Mile commercial fleet warranty covering structural casting and internal moving components. The heavy-duty wood crate contains one remanufactured long block engine, a complete engine install gasket set, spark plug well seals, front timing cover seals, dyno test documentation, and priming instructions.