BluePrint BP302CTCD Ford 302 361HP Dressed Long Block Crate Engine
Description
Eliminate tedious valvetrain and induction guesswork with the BluePrint BP302CTCD Crate Engine in dressed long block configuration. Displacing 302 cubic inches, this small-block Ford Windsor produces 361 horsepower at 5,500 RPM and 340 lb-ft torque at 4,000 RPM. Outfitted with high-flow aluminum heads, carburetor, dual-plane intake, distributor, and water pump, it furnishes turn-key muscle car motivation straight from the freight skid.
A blueprinted cast iron Ford Windsor block forms the rigid structural foundation, equipped with a leak-resistant 1-piece rear main seal. Inside resides an externally balanced rotating group: a cast steel crankshaft, forged connecting rods, and 9.5:1 hypereutectic pistons across 4.000-inch bores. Oil stays secure inside an external 50-ounce imbalance dual-sump steel oil pan with internal oil splash baffles.
Key Features of BluePrint BP302CTCD
Classic car restorers choose to buy BluePrint BP302CTCD crate engine packages to eliminate parts procurement headaches during vehicle repower projects. The turn-key configuration fits vintage Ford Mustangs, Fairlanes, and custom F-100 pickups with ease.
- 600 CFM four-barrel carburetor comes pre-calibrated to ensure crisp throttle response and clean combustion straight from the crate.
- Dual-plane aluminum intake manifold maximizes low-end torque while promoting even fuel distribution across all eight cylinders.
- High-flow aluminum cylinder heads dissipate excess heat to suppress engine knock on premium service-station fuel supplies.
- Hydraulic flat-tappet camshaft profiles reduce friction while optimizing valve lift for smooth idle and strong mid-range pull.
- Electronic distributor provides simple one-wire ignition hookup and steady spark delivery past 5,500 RPM.
- BluePrint BP302CTCD complete powertrain packages include a cast iron water pump with factory Ford accessory drive spacing.
- Harmonic balancer arrives installed on the crankshaft snout to streamline front accessory installation.
- 1.6:1 ratio roller rockers guide valves accurately without valve stem galling during hard acceleration runs.
Dyno Profile Valvetrain Behavior
Dynamometer validation certifies 361 horsepower at 5,500 RPM and 340 lb-ft torque at 4,000 RPM across a broad 2,000 to 5,800 RPM range. Designed for 91-octane pump gasoline, the combusion chambers resist detonation under hot weather conditions. Camshaft timing provides 15 in-Hg manifold vacuum at 800 RPM, while internal oiling passages maintain 45 to 65 PSI when warm.
Chassis Compatibility Bellhousing Points
Built within traditional Ford Windsor dimensions, the package clears front shock towers in classic Mustangs without modification. The crank tail requires an external 50-ounce imbalance flexplate or flywheel to bolt straight to common Ford automatics or manual transmissions. Factory motor mount positions eliminate clearance headaches around full-length exhaust headers and manual steering linkages.
Break-In Instructions Usage Parameters
Prime the engine using a mechanical shaft tool through the distributor hole to protect internal surfaces before turning the starter. Use 10W-30 break-in oil rich in ZDDP zinc additives to lubricate internal bearing shells. This turn-key engine is not engineered for marine closed-compartment use, boost surpassing 6 PSI, or continuous alcohol fuel operation.
- Discard break-in engine oil and install a high-efficiency filter canister after the first 500 road miles.
- Inspect carburetor throttle linkage, fuel line fittings, and baseplate bolts every 3,000 miles of street use.
- Check ignition distributor advance weights, rotor contacts, and spark wires every 12 months or 12,000 miles.
Factory Guarantee Crate Contents
BluePrint protects your investment with a 30-Month or 50,000-Mile factory warranty against defects in components or machining. The wooden crate contains the complete engine, carburetor, intake manifold, distributor, plug wires, water pump, harmonic balancer, oil pan, valve covers, and dyno record sheet.
BluePrint BP302CTCD Ford 302 CID 361 HP Dressed LB Specs
| Brand | BluePrint Engines |
| Engine Model | BP302CTCD |
| Part Type | Crate Engines |
| Product Line | BluePrint Engines Ford 302 C.I.D. 361 HP Dressed Long Block Crate Engines |
| UPC | 00887753841308 |
| Crate Engine Family | Ford Windsor |
| Actual Engine Displacement | 5.0L/302 |
| Cylinder Head Material | Aluminum |
| Engine Block Material | Cast iron |
| Advertised Compression Ratio | 9.4:1 |
| Assembled | Yes |
| Engine Balance | External, 50 oz. imbalance |
| Cam Style | Hydraulic roller, OE roller |
| Rear Main Seal Style | 1-piece |
| Intake Manifold Included | Yes |
| Intake Manifold Style | Carbureted |
| Cylinder Heads Included | Yes |
| Carburetor Included | Yes |
| Throttle Body Included | No |
| Distributor Included | Yes |
| Oil Pan Included | Yes |
| Valve Covers Included | Yes |
| Timing Cover Included | Yes |
| Water Pump Included | Yes |
| Harmonic Balancer Included | Yes |
| Flexplate Included | No |
| Flywheel Included | No |
| Air Cleaner Included | Yes |
| Spark Plugs Included | Yes |
| Spark Plug Wires Included | Yes |
| Computer Included | No |
| Wiring Harness Included | No |
| Supercharger Included | No |
| Warranty Info | 30-Month / 50,000 Miles |
You must be logged in to post a review.







Reviews
There are no reviews yet.